Siemens 6AG1132-6FD00-7CU0 Digital Output Module
| Company Information | ||||||||
| [email protected] | ||||||||
| Mobile | +8613666084105 | |||||||
| +8613666084105 | ||||||||
| 13666084105 | ||||||||
| Add to | Room 1004, No. 62 Xiangxiu Li, Siming District, Xiamen City, Fujian Province, China | |||||||
Technical Specifications
| Parameter | Specification |
|---|---|
| Brand | Siemens |
| Product Model | 6AG1132-6FD00-7CU0 |
| Product Series | SIPLUS ET 200SP |
| Product Type | Digital Output Module |
| Product Designation | DQ 4×24…230V AC/2A HF |
| Standard Reference Model | 6ES7132-6FD00-0CU0 |
| Number of Digital Outputs | 4 |
| Output Type | Triac |
| Output Signal | AC |
| Rated Output Voltage | 230 V AC |
| Output Voltage Range | 24–230 V AC |
| Rated Output Current | 2 A per channel |
| Maximum Output Current | Up to 4 A under specified conditions; refer to derating requirements |
| Maximum Total Module Current | 8 A |
| Rated Module Supply Voltage | 230 V AC |
| Supply Frequency | 47–63 Hz |
| Permissible Supply Voltage Range | 20.4–264 V AC |
| Output Configuration | Current-sourcing |
| Operating Modes | DQ, DQ with energy-saving function, power control |
| Power Control Functions | Phase-angle control, half-wave control and full-wave control |
| Phase-Angle Control Range | 8.5–100% |
| Maximum Resistive Load | 2 A per channel; higher current requires compliance with specified conditions |
| Maximum Inductive Load | 2 A per channel |
| Maximum Lamp Load | 100 W |
| Output Delay | Maximum 40 ms (OFF to ON); 20 ms (ON to OFF) with resistive load |
| Maximum Switching Frequency | 10 Hz for resistive and inductive loads; 1 Hz for lamp loads in DQ mode |
| Short-Circuit Protection | Not integrated; external fusing required |
| Overload Protection | Not integrated; external protection required |
| Open-Circuit Detection | Yes, channel by channel |
| Residual Current in OFF State | Maximum 3 mA |
| Diagnostic Functions | Supply voltage monitoring, wire-break detection, group error and channel diagnostics |
| Diagnostic Alarm | Supported |
| Substitute Value Function | Supported |
| Status Indicators | PWR, channel status, Fn and DIAG LEDs |
| Compatible BaseUnit | BU type U0 |
| Color Code | CC20 |
| Connection Configuration | 1-wire and 2-wire; 3-wire with potential distributor module |
| Output Address Space | 8 bytes |
| QI Information | 1 byte |
| Firmware Update | Supported |
| Identification and Maintenance Data | I&M0 to I&M3 |
| Typical Power Loss | 9 W at 230 V AC, 50 Hz, with all outputs loaded at 2 A |
| Isolation Test Voltage | 2,545 V DC / 2 s |
| Operating Temperature | -40 to +70°C ; -40 to +50°C |
| Maximum Total Current at 40°C | 8 A for horizontal installation, subject to channel-current limits |
| Maximum Total Current at 50°C | 6 A for horizontal installation, subject to channel-current limits |
| Maximum Total Current at 60°C | 4 A for horizontal installation, subject to channel-current limits |
| Maximum Total Current at 70°C | 2 A for horizontal installation |
| Maximum Installation Altitude | 2,000 m above sea level |
| Conformal Coating | Yes |
| Dimensions | 20 × 73 × 58 mm |
| Weight | 0.05 kg |
FAQ
Q1: What is the main function of the Siemens 6AG1132-6FD00-7CU0 Digital Output Module?
The Siemens 6AG1132-6FD00-7CU0 is a SIPLUS ET 200SP high-feature digital output module designed for controlling AC loads in industrial automation systems. It provides four Triac-based output channels and supports switching AC loads from 24 V to 230 V. In addition to conventional digital switching, the module offers power control functions, making it suitable for applications involving heating elements, industrial actuators and other AC-operated equipment. It can be integrated into distributed I/O architectures controlled by a SIMATIC automation system.
Q2: What is the difference between the 6AG1132-6FD00-7CU0 and a standard DC digital output module?
The main difference is the output technology and the type of load being controlled. The 6AG1132-6FD00-7CU0 uses Triac outputs for AC loads, supporting an output voltage range of 24–230 V AC. Standard DC output modules generally use transistor switching and are intended for DC loads such as 24 V solenoid valves and relay coils. This Siemens module also supports phase-angle, half-wave and full-wave power control, which provides more flexibility for AC power regulation than a conventional on/off DC output module.
Q3: How many output channels does the 6AG1132-6FD00-7CU0 provide, and what is the rated current?
The module provides four independent digital output channels, each rated at 2 A. The maximum total output current per module is 8 A under the specified operating conditions. Higher current values, including operation up to 4 A on an individual channel, are subject to specific load and derating conditions. Engineers should calculate the current requirements of each connected load and check the module’s temperature-dependent limits before commissioning. The total current must not exceed the permitted module rating.
Q4: Which operating modes are supported by the 6AG1132-6FD00-7CU0?
The module supports standard DQ switching and DQ operation with an energy-saving function. It also provides power control modes, including phase-angle control, half-wave control and full-wave control. Phase-angle control offers an adjustable control range of approximately 8.5–100% of the phase angle. These functions allow the module to regulate AC power rather than simply switching a load on or off. The appropriate mode should be selected according to the load characteristics and application requirements in the PLC configuration.
Q5: Does the 6AG1132-6FD00-7CU0 have built-in short-circuit protection?
No. The module does not provide integrated short-circuit or overload protection. External fusing is necessary to protect the module and connected circuits. Siemens specifies a fast-acting miniature fuse in the module supply, with the appropriate rating and tripping characteristics selected according to the installation requirements. Before energizing the system, engineers should verify fuse selection, wiring insulation, load current and the AC supply arrangement. Relying on the module’s diagnostic functions as a substitute for electrical protection is not recommended.
Q6: What diagnostic functions are available on this digital output module?
The 6AG1132-6FD00-7CU0 supports supply voltage monitoring, channel-by-channel wire-break detection, group error reporting and diagnostic alarms. It also provides LED indicators for power status, channel status and diagnostic conditions. These functions help maintenance personnel identify wiring problems and supply-related faults without checking every field circuit manually. One important limitation is that the module does not provide short-circuit diagnostics. External protection and appropriate electrical testing are therefore necessary when investigating suspected short circuits.
Q7: Which BaseUnit should be used with the Siemens 6AG1132-6FD00-7CU0?
This module is designed for use with a BU type U0 BaseUnit. A one-wire or two-wire connection can be implemented with the appropriate U0 BaseUnit configuration. For three-wire wiring, a compatible potential distributor module is required. Correct BaseUnit selection is important for proper electrical connection, potential distribution and reliable operation. Before installation, engineers should confirm the terminal arrangement, wiring requirements and compatibility with the existing ET 200SP station.
Q8: What precautions should be taken when installing the 6AG1132-6FD00-7CU0 in an industrial control cabinet?
The module supports an operating temperature range of -40 to +70°C for horizontal installation and -40 to +50°C for vertical installation. However, its maximum permissible output current decreases as the ambient temperature increases. For horizontal installation, the specified total current limits are 8 A up to 40°C, 6 A up to 50°C, 4 A up to 60°C and 2 A up to 70°C, subject to the applicable channel-current restrictions. Engineers should also provide suitable external fusing, maintain adequate cabinet ventilation, separate AC output wiring from sensitive signal cables and verify the grounding and potential distribution arrangement. These measures help prevent overheating, wiring faults and unexpected output behavior.
Siemens 6AG1132-6FD00-7CU0 Digital Output Module is in stock. Please contact us for a quick quote and competitive pricing.
| Company Information | ||||||||
| [email protected] | ||||||||
| Mobile | +8613666084105 | |||||||
| +8613666084105 | ||||||||
| 13666084105 | ||||||||
| Add to | Room 1004, No. 62 Xiangxiu Li, Siming District, Xiamen City, Fujian Province, China | |||||||
Company Introduction
Xiamen Shengruite Trading Co., Ltd. is a company specializing in the supply of industrial PLC spare parts.
We provide high-quality PLC spare parts to customers in the global manufacturing, energy and power, chemical and other fields.
Since its establishment in 2011, after 13 years of rapid development, the cumulative global shipments have reached 223,650 pieces, with an annual output value of US$50 million.
Successfully served more than 500 customers in more than 100 countries and regions including Saudi Arabia, UAE, the United States, Europe, Africa, and Southeast Asia
Our Mission
Provide customers with the best quality PLC spare parts and the fastest delivery service to ensure that their industrial automation systems are always in the best operating condition.
We provide a 1-year warranty service, and we support returns and exchanges for any issues to ensure your rights and interests are fully protected.
We can provide detailed product images upon request, and our team can arrange warehouse photos for confirmation to ensure you have all the information you need before making a purchase.
Shipping times vary depending on your location. With the support of our 16 global warehouses, we strive to deliver orders as quickly as possible. Contact us to get an estimated delivery time for your specific location.
The minimum order quantity (MOQ) is typically one unit. However, for larger orders, please contact us for potential discounts and pricing details.
Yes, we offer competitive pricing for bulk purchases. Please reach out to our sales team with the specifics of your order to receive a custom quote.
We accept various payment methods for wholesale orders, including bank transfers (T/T), letters of credit, and other options upon agreement. For large transactions, please contact us directly for payment terms.
Yes, we offer flexible ordering options for both small and large quantities. Whether youre looking for a single unit or a large batch, we can accommodate your needs.
We occasionally offer promotional discounts for new wholesale customers. Contact us to learn more about any current offers available for first-time buyers.
If you are unsure of compatibility with your existing setup please provide your system details and our support team can verify compatibility prior to purchase.
Returns are accepted within 30 days if the product is unused, unopened, and in its original packaging. Please note that return shipping and associated costs are the buyer\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\’s responsibility.
Yes, we offer technical support for the installation and integration of our products. Our team can assist with setup, configuration, and troubleshooting to ensure a smooth installation.








